On Board Transponder Chip Programming Instructions for select vehicles

ON-BOARD PROGRAM

1

GENERAL MOTORS*
PK3 & “CIRCLE-PLUS”

ADD DUPLICATE KEY (Requires at least one working key):

1. Verify that the new key has “PK3” or “+” stamped on it.

2. Insert the original, already programmed key into the ignition lock cylinder and start the engine. If the engine will not start, see your dealer for service.

3. After the engine has started, turn the key to LOCK/OFF and remove the key.

4. Insert the key to be programmed and turn it to ON/RUN within 10 seconds of removing the previous key. The security light will turn off once the key has been programmed. It may not be apparent that the security light went on due to how quickly the key is programmed. (If your vehicle does not have a security light (04-07 Grand Prix, Bonneville, Impala), wait 10 minutes 45 seconds to make sure the key has been programmed).

5. Repeat steps 1 through 4 if additional keys are to be programmed.

ON-BOARD PROGRAM

2

1997 FORD, LINCOLN, MERCURY 1998 NAVIGATOR/EXPEDITION

ORIGINATE NEW MASTER KEY:

1. Put the new key into the ignition. Turn it to the ON position. The dashboard security light will flash for 15 minutes. Once the dashboard security light stops flashing, you have five minutes to begin Step 2.

2. Turn the ignition OFF and then back to the ON position. The dashboard security light will flash for 15 additional minutes.

3. Repeat Step 2.

4. Once the dashboard security light has turned off for the third time, the key will be able to function in the car. It has been programmed into the car’s computer and has replaced ALL previous electronic key codes — the computer will not recognize any other key.

ADD DUPLICATE KEY:

1. Put the current key into the ignition.

2. Turn the ignition ON and back to OFF.

3. Remove the current key and insert the new key, turning it ON. You MUST do this within 15 seconds.

4. The security light will switch on for two seconds, confirming that the key has been successfully programmed into the vehicle.

ON-BOARD PROGRAM

3

1998+ FORD, LINCOLN, MERCURY

ADD KEY (Requires two working keys):

1. Put a current key into the ignition.

2. Turn the ignition to ON, then back to the OFF position.

3. Remove the key and insert a second key. Turn it ON and back to the OFF position. You MUST do this within five seconds.

4. Before ten seconds have elapsed, put a new key in and turn the ignition ON. After one second, turn the key back to the OFF position.

5. The dashboard security light will glow for three seconds. This confirms the programming of the new key has been successful.

ON-BOARD PROGRAM

4

1998-2 001 TOYOTA, LEXUS

TO DELETE ALL BUT ONE KEY FROM THE UNIT:

1. Depress and release brake and accelerator pedals once, doing both at the same time.

2. Put an existing master key into the ignition. Leave the key in the LOCK position; do not turn it.

3. Press and release the accelerator pedal, six times, within 15 seconds of inserting the key.

4. Within 20 seconds of Step 3, press and release the brake pedal seven times.

5. The dashboard security light will flash. This confirms that all keys (except the one currently being used) have been deleted.

6. Within ten seconds, remove the key from the ignition cylinder. This is now the only key still programmed to work.

ADD KEY:

1. Press and release the brake and accelerator pedals once, doing both at the same time. 2. Put the existing master key into the ignition.
3. Press and release the accelerator pedal five times within 15 seconds.
4. Press and release the brake pedal six times within 20 seconds and remove key.

5. Insert new key into ignition within ten seconds.
6. Press and release the accelerator pedal once within ten seconds.
7. The security light will turn off after 80 seconds. This indicates that the new key is now registered. 8. Remove new key. Press and release the brake pedal once.

ON-BOARD PROGRAM

5

EXCEPT MITSUBISH BASED CHRYSLER VEHICLES 1998+ CHRYSLER, DODGE
1999+ JEEP

ADD KEY (Must have two working Sentry Keys):

1. Put one of the two current keys into the ignition and turn to the ON position.

2. After the key has been in the ON position for at least three seconds — but no more than 15 seconds — turn the key back to the OFF position.

3. Take the key out and put in the second current key, turning it to the ON position, all within 15 seconds. The second key cannot be the same as the first key.

4. After ten seconds, a theft alarm light will illuminate and a single chime will sound. This confirms entry into “Customer Programming Mode”.

5. Within 60 seconds, turn key OFF and remove the current key.

6. Put a new key into the ignition and turn to the ON position.

7. After ten seconds, a single chime will sound. The theft alarm light will turn off. Wait three seconds and turn key OFF.

8. Repeat these steps for additional keys.

ON-BOARD PROGRAM

6

2 000-2 005 FORD FOCUS, FORD ESCAPE 2 001-2 003 MAZDA TRIBUTE ONLY

ORIGINATE NEW MASTER KEY:

Two working keys are required to program additional keys with this on-board programming method.

ADD KEY (Requires two working keys):

1. Put the existing key into the ignition.

2. Turn the ignition ON, then turn it OFF again.

1. Within five seconds, take out the existing key and put in a second key, turning it to ON and back OFF.

2. Within ten seconds, put in the new key and turn it on. After one second, turn it OFF.

3. The security light will glow for three seconds. This confirms the new key has been programmed successfully.

ON-BOARD PROGRAM

7

2 002 -2 010 TOYOTA, LEXUS

Keys can be programmed using the Code-Seeker on most 32 bit systems. The 2003-2007 Sequoia requires flashing.

TO DELETE ALL BUT ONE KEY FROM THE UNIT:

1. Simultaneously depress and release brake and accelerator pedals 1 time.

2. Insert an existing master key into the ignition cylinder. Do not turn the key from the OFF (LOCK) position.

3. Within fifteen seconds of inserting the key, depress and release the accelerator pedal six times.

4. Within twenty seconds of completing the above step, depress and release the brake seven times.

5. The security light will flash, indicating all keys other than the one being used have been deleted.

6. Remove the key from the ignition cylinder within ten seconds. It will be the only key still programmed to work.

ADD DUPLICATE KEY:

Requires one working Toyota/Lexus Master key.

1. Make sure all doors and windows are closed.

2. Insert Master key into the ignition cylinder.

3. Cycle the ignition cylinder from ON to OFF five times.

4. Open and close the driver side door six times.

5. Remove the Master key and insert the new duplicate key.

6. TURN THE IGNITION CYLINDER ON.

7. The new key will be registered after 60 seconds. The THEFT light on the dashboard will go out, indicating that the programming has been completed.

ON-BOARD PROGRAM

8

FORD/LINCOLN/MERCURY IKT

ADD KEY (Must have two working original keys):

1. Insert the first previously programmed coded keys into the ignition.

2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least 3 seconds, but no more than 10 seconds.

3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition.

4. Within 10 seconds of turning the ignition to the 1 (LOCK) position, insert the second previously coded key into the ignition.

5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least 3 seconds, but no more than 10 seconds.

6. Turn the ignition to the 1 (LOCK) position and remove the second coded key from the ignition.

7. Within 20 seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key, insert the new un-programmed key (new key/valet key) into the ignition.

8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least 6 seconds.

9. Remove the newly programmed coded key from the ignition.

If the key has been successfully programmed, it will start the vehicle’s engine and will operate the remote entry system (if the new key is an Integrated Keyhead Transmitter). The theft indicator light will illuminate for 3 seconds and then go out to indicate successful programming.

If the key was not successfully programmed, it will not start your vehicle’s engine and/or will not operate the remote entry features. The theft indicator light may flash on and off. Wait 20 seconds and you may repeat Steps 1 through 8. If the failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed.

To program additional new un-programmed key(s), wait 20 seconds and then repeat this procedure from Step 1.

ON-BOARD PROGRAM

9

CHRYSLER/DODGE/JEEP INTEGRATED KEY

ADD KEY (Must have two working integrated keys):

1. Insert first working integrated key into the ignition switch and turn the ignition switch to the ON position for at least 3 seconds, but no longer than 15 seconds. Turn the ignition switch to the LOCK position and remove the first key.

2. Insert the second working integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

3. Insert a blank integrated key into the ignition switch and turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound and the Vehicle Security Alarm Indicator Light will stop flashing. Turn on again for 3 seconds and then turn off.

The new integrated key is programmed. The Remote Keyless Entry (RKE) transmitter will also be programmed during this procedure.

Repeat this procedure to program up to 8 keys.

ON-BOARD PROGRAM

10

GM HIGH SECURITY SIDE-MILL

ADDING KEYS (North America, except Canada):

NOTE:

• To initiate, this procedure requires that a learned master key be available.

• A total of 10 keys may be programmed to a single vehicle.

• This procedure adds keys only. The procedure does not erase previously learned keys.

• The keys to be learned must duplicate the mechanical cut of the current key.

• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.

1. With a previously learned master key, turn ON the ignition, with the engine OFF.

2. Turn OFF the ignition and remove the key.

3. Within 10 seconds of turning OFF the ignition, insert the key to be learned and turn ON the ignition. The vehicle has now learned the new key.

ON-BOARD PROGRAM

10b

GENERAL MOTORS HIGH SECURITY PHILLIPS ENCRYPTED

2 014-2 016 CHEVROLET SILVERADO AND GMC SIERRA, 2 015-2 016 CHEVROLET COLORADO AND GMC CANYON

Programming with a Recognized Key (Key Vehicles Only) Up to eight (8) keys can be programmed to the vehicle.

TO PROGRAM A NEW KEY:

1. Insert the original, already programmed key in the ignition and turn the key to the ON/RUN position.

2. Turn the key to LOCK/OFF, and remove the key.

3. Insert the new key to be programmed and turn it to the ON/RUN position within five (5) seconds. The security light will turn off once the key has been programmed.

4. Repeat steps 1-5 if additional keys are to be programmed.

If a key is lost or damaged, see your dealer to have a new key made.

PROGRAMMING WITHOUT A RECOGNIZED KEY (KEY VEHICLES ONLY)

Program a new key to the vehicle when a recognizable key is not available. Canadian regulations require that Canadian owners see their dealer.

If there are no currently recognized keys available, follow this procedure to program the first key.

ON-BOARD PROGRAM

10b

GENERAL MOTORS HIGH SECURITY PHILLIPS ENCRYPTED (continued)

This procedure will take approximately 30 minutes to complete for the first key. The vehicle must be off and all of the keys must be with you.

1. Insert the new vehicle key into the ignition.

2. Turn to ON/RUN. The security light will come on.

3. Wait 10 minutes until the security light turns off.

4. Turn the ignition to LOCK/OFF.

5. Repeat steps 2-4 two more times. After the third time, turn to ON/RUN; the key is learned and all previously known keys will no longer work the vehicle.

Remaining keys can be learned by following the procedure in “Programming with a Recognized Key (Key Vehicles Only).”

ON-BOARD PROGRAM

11

GM HIGH SECURITY - PEPS

PROGRAMMING TRANSMITTERS TO THE VEHICLE:

• Only keyless access transmitters programmed to the vehicle will work.

• If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer.

• The vehicle can be reprogrammed so that lost or stolen transmitters no longer work.

• Any remaining transmitters will need to be reprogrammed. Each vehicle can have up to five transmitters matched to it.

  PROGRAMMING WITH A RECOGNIZED TRANSMITTER:

  A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.

1. Place the recognized transmitter(s) in the cupholder.

2. Insert the vehicle key of the new transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver Information Center (DIC) displays “Ready For Remote #2, 3, 4 or 5.”

3. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.

4. Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.

5. Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5. When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

ON-BOARD PROGRAM

11

GM HIGH SECURITY PEPS (continued)

PROGRAMMING WITHOUT A RECOGNIZED TRANSMITTER:

If there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you.

1. Insert the vehicle key of the new transmitter into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver Information Center (DIC) displays “Remote Learn Pending, Please Wait.”

2. Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”

3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”

4. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.

5. Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.

6. Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

STARTING THE VEHICLE WITH A LOW TRANSMITTER BATTERY:

If the transmitter battery is weak, the DIC may display “No Remote Detected” when you try to start the vehicle. The “Replace Battery” in Remote Key message may also be displayed at this time.

TO START THE VEHICLE:

1. Remove the cupholder from the center console storage area.

2. Place the transmitter in the transmitter pocket with the buttons facing up.

3. With the vehicle in “P” (Park) or “N” (Neutral), press the brake pedal and the ignition control. See “Starting the Engine”, for additional information about the vehicle’s keyless ignition with push start.

Replace the transmitter battery as soon as possible.

BATTERY REPLACEMENT:

Replace the battery if the “Replace Battery in Remote Key” message displays in the DIC. See “Replace Battery in Remote Key” under Key and Lock Messages.

The battery is not rechargeable. See your dealer/retailer to replace the battery.

ON-BOARD PROGRAM

12

2 010-2 013 FORD TRANSIT CONNECT

REMOTE KEYLESS ENTRY (RKE) TRANSMITTER PROGRAMMING:

NOTE: A maximum of 4 Remote Keyless Entry (RKE) transmitters can be programmed to the vehicle. Programming must be done at the same time for all the RKE transmitters.

1. NOTE: Make sure the front doors are unlocked and closed, and the ignition is in the OFF position.

   Turn the ignition switch from the OFF to the RUN position 4 times in rapid succession (within 6 seconds), with the fourth turn ending in OFF. If the Generic Electronic Module (GEM) successfully enters program mode, the Instrument Cluster (IC) sounds a chime.

2. NOTE: If no action is taken within 10 seconds after a transmitter has been programmed, the programming sequence ends.

   Within 10 seconds, press any button on the RKE transmitter to be programmed. The IC chimes to confirm that each RKE transmitter is programmed.

   Repeat this step for each RKE transmitter.

3. NOTE: There are NO chimes or any other confirmation from the IC upon exiting programming mode. Exiting the programming mode is accomplished if one of the following occurs:

   • The ignition transitions to the RUN position.

   • 10 seconds have passed since entering programming mode or since the last RKE transmitter was programmed.

   • The maximum number (4) of RKE transmitters have been programmed.

4. Check the operation of the transmitter. If the door locks do not respond for the programmed RKE transmitter(s), wait several seconds and press the button again. If the door locks still fail to respond, refer to the Handles, Locks, Latches and Entry Systems Section in the owners’ manual. (Make sure that no more than the maximum number of RKE transmitters are attempted to be programmed.)

KEY PROGRAMMING – PROGRAM A KEY USING TWO PROGRAMMED KEYS:

NOTES:

• This procedure is only for vehicles without Intelligent Access (IA). For vehicles with IA, the keys can only be programmed using a scan tool.

• This procedure works only if 2 or more programmed keys are available. If 2 programmed keys are not available, refer to Key Programming Using Diagnostic Equipment in your owners manual.

• This procedure only programs the Passive Anti-Theft System (PATS) portion of the key into the Instrument Panel Cluster (IPC). It does not program the Remote Keyless Entry (RKE) Transmitter Identification Code (TIC) into the Body Control Module (BCM).

1. Insert the first programmed PATS key into the ignition and turn the key from the OFF position to the RUN position (maintain the key in the RUN position for approximately 3 seconds).

2. Turn the first key to the OFF position and remove the key from the ignition.

3. Within 10 seconds of turning the key to the OFF position, insert a second programmed PATS key into the ignition and turn the key from the OFF position to the RUN position (maintain the key in the RUN position for approximately 3 seconds).

4. Turn the second key to the OFF position and remove the key from the ignition.

5. Within 10 seconds of turning the key to the OFF position, insert the new unprogrammed PATS key into the ignition and turn the key from the OFF position to the RUN position (maintain the key in the RUN position for approximately 3 seconds).

6. If it is desired to program additional key(s) (up to a total of 8 keys can be programmed), repeat steps 1 – 5 for each additional key.

7. Refer to RKE Transmitter Programming above to program the RKE portion of the key.

ON-BOARD PROGRAM

13

2 011-2 014 FORD FIESTA

REMOTE KEYLESS ENTRY (RKE) TRANSMITTER PROGRAMMING:

NOTES:

• A maximum of 8 Remote Keyless Entry (RKE) transmitters can be programmed to the vehicle.

  Programming must be done at the same time for all RKE transmitters.

• This procedure is for programming the RKE transmitter portion of the Integrated Keyhead Transmitter (IKT). The RKE transmitter for an Intelligent Access (IA) key is programmed automatically during the key programming. Refer to the key programming procedures under Anti-Theft – Passive Anti-Theft System (PATS) below.

  1. Use the door lock control switch to electronically unlock the door locks.

  NOTES:

  • There is no audible or visual indication that programming mode has been entered.

  2. Turn the ignition from the OFF to RUN position 4 times in rapid succession (within 6 seconds), with the fourth turn ending in OFF.

  NOTES:

• If no action is taken within 10 seconds after a transmitter has been programmed, the programming sequence ends.

1. Within 10 seconds, press any button on the RKE transmitter to be programmed. After the first RKE transmitter is programmed, press a button on each subsequent transmitter to be programmed (each within 10 seconds of each other).

2. Exiting the programming mode is accomplished if one of the following occurs:

• The key transitions to the RUN position.

• 10 seconds have passed since entering programming mode or since the last RKE transmitter was programmed.

• The maximum number (8) of RKE transmitters have been programmed.

5. Check the operation of the transmitter. If the door locks do not respond for the programmed RKE transmitter(s), wait several seconds and press the button again. If the door locks still fail to respond, refer to Handles, Locks, Latches and Entry Systems in your owners manual.

KEY PROGRAMMING – PROGRAM A KEY USING TWO PROGRAMMED KEYS

NOTES:

• This procedure is only for vehicles without Intelligent Access (IA). For vehicles with IA, the keys can only be programmed

  using a scan tool.

• This procedure works only if 2 or more programmed keys are available. If 2 programmed keys are not available, refer to Key Programming Using Diagnostic Equipment in your owners manual.

• This procedure only programs the Passive Anti-Theft System (PATS) portion of the key into the Instrument Panel Cluster (IPC). It does not program the Remote Keyless Entry (RKE) Transmitter Identification Code (TIC) into the Body Control Module (BCM).

1. InsertthefirstprogrammedPATSkeyintotheignitionandturnthekeyfromtheOFFpositiontotheRUNposition (maintain the key in the RUN position for approximately 3 seconds).

2. Turn the first key to the OFF position and remove the key from the ignition.

3. Within 10 seconds of turning the key to the OFF position, insert a second programmed PATS key into the ignition and turn the key from the OFF position to the RUN position (maintain the key in the RUN position for approximately 3 seconds).

4. Turn the second key to the OFF position and remove the key from the ignition.

5. Within 10 seconds of turning the key to the OFF position, insert the new unprogrammed PATS key into the ignition and turn the key from the OFF position to the RUN position (maintain the key in the RUN position for approximately 3 seconds).

6. If it is desired to program additional key(s) (up to a total of 8 keys can be programmed), repeat steps 1 – 5 for each additional key.

7. Refer to RKE Transmitter Programming above to program the RKE portion of the key.

ON-BOARD PROGRAM

14

2 012 -2 014 FORD FOCUS/ESCAPE

ADD KEY (Must have two working original keys):

NOTE:
A maximum of eight coded keys can be programmed to your vehicle; all eight can be IKT’s with remote entry functionality.

1. Insert the first previously programmed coded keys into the ignition.

2. Turn the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.

3. Turn the ignition off and remove the first coded key from the ignition.

4. After 3 seconds but within ten seconds of turning the ignition off, insert the second previously coded key into the ignition.

5. Turn the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.

6. Turn the ignition off and remove the second coded key from the ignition.

7. After three seconds but within 10 seconds of turning the ignition off and removing the previously programmed coded key, insert the new un-programmed key (new key/valet key) into the ignition.

8. Turn the ignition from off to on. Keep the ignition on for at least 6 seconds.

9. Remove the newly programmed coded key from the ignition.

10. If the key has been successfully programmed, it will start the vehicle’s engine and will operate the remote entry system (if the new key is an Integrated Keyhead Transmitter).

If the key was not successfully programmed, it will not start your vehicle’s engine and/or will not operate the remote entry features. The message center will display: NO KEY DETECTED. Wait 10 seconds and you may repeat Steps 1 through 8. If the failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed.

To program additional new un-programmed key(s), wait 20 seconds and then repeat this procedure from Step 1.

ON-BOARD PROGRAM

15

2 010-2 014 FORD TAURUS/ EDGE/EXPLORER/ LINCOLIN MKS/MKT

NOTE:
A maximum of four intelligent access keys can be programmed to your vehicle. If you would like to replace a previously programmed access key with a new access key, or if you already have four access keys programmed to your vehicle, you must take your vehicle and all access keys to your authorized dealer to be erased and reprogrammed.

ADDING SPARE INTELLIGENT ACCESS KEYS:

You must have two previously programmed intelligent access keys inside the vehicle and the new un-programmed intelligent access keys readily accessible. If two previously programmed keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.

Ensure that the vehicle is off before beginning this procedure. Ensure that all doors are closed before beginning this procedure and that all doors remain closed throughout the procedure. Perform this procedure exactly as described below, and perform all steps within 30 seconds of starting the sequence. If any steps are performed out of sequence, stop and wait at least one minute before starting again.

Please read and understand the entire procedure before you begin.

1. Place the new un-programmed intelligent access key in the pocket inside the center console utility compartment.

2. Press the driver or passenger power door unlock control three times.

3. Press and release the brake pedal one time.

4. Press the driver or passenger power door lock control three times.

5. Press and release the brake pedal one time. The indicator on the Start/Stop button should begin to rapidly flash, indicating that the programming mode has been entered and two programmed intelligent access keys have been detected in the vehicle.

6. Within one minute, press the start/stop button. A message will be displayed on the message center indicating that the new Intelligent Access Key was programmed. If four intelligent access keys have already been programmed to your vehicle, you cannot program anymore and the message.

MAX # OF KEYS LEARNED will be displayed on the message center.

1. Remove Intelligent Access Key from utility compartment pocket and press the unlock or lock control on the newly programmed intelligent access keys to exit programming mode.

2. Verify that the remote entry functions operate (lock, unlock) and that the vehicle starts with new Intelligent Access Key.

If the Intelligent Access Key has been successfully programmed, it can be used to activate the Intelligent Access with Push Button Start feature and can be used to start your vehicle.

ON-BOARD PROGRAM

16

MOST GM VEHICLES 2 006-2 010

NOTE:
On-Board Programming for use in most GM vehicles for model years 2006-2010. Some vehicles may require a dealer or aftermarket programming tool. Most GM vehicles for model years 2011- 2012 require a dealer or aftermarket programming tool.

USE THIS PROCEDURE FOR VEHICLES WITH DRIVER INFORMATION CENTER BUTTONS:

RELEARN REMOTE:

This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters.

1. Press the vehicle information button until PRESS V TO RELEARN REMOTE displays.

2. Press the set/reset button until REMOTE LEARNING ACTIVE is displayed.

3. Press and hold the lock and unlock buttons on the first transmitter at the same time for about 15 seconds. On vehicles with memory recall seats, the first transmitter learned will match driver 1 and the second will match driver 2. A chime will sound indicating that the transmitter is matched.

4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it.

5. To exit the programming mode, you must cycle the key to LOCK/OFF.

USE THIS PROCEDURE FOR VEHICLES WITHOUT DRIVER INFORMATION CENTER BUTTONS:

RELEARN REMOTE:

To access this display, the vehicle must be in P (Park). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display.

3. Press and hold the lock and unlock buttons on the keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

ON-BOARD PROGRAM

17

CADILLAC CTS & ESCALADE 2 007-2 014

VEHICLES EQUIPPED WITH A “DRIVERS INFORMATION CENTER” OR DIC

1. Insert key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until “PRESS TO RELEARN REMOTE KEY” displays

3. Press the set/reset button until “REMOTE KEY LEARNING ACTIVE” displays.

4. Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 15 seconds. (On vehicles with memory recall seats, the first remote learned will match driver 1 and the second will match driver 2.)

5. To program additional remotes at this time, repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode, turn key off and remove key. Test remote(s).

ON-BOARD PROGRAM

18

MOST
1998+ FORD, LINCOLN, MERCURY VEHICLES

Except Lincoln LS before 2002 (must use OEM Programmer) To reprogram the remote entry transmitters:

1. 2. 3. 4.

5. 6.

7.

8. 9.

Ensure the vehicle is electronically unlocked.

Put the key in the ignition.

Turn the key from the LOCK position to RUN.

Cycle eight times rapidly (within 10 seconds) between the LOCK position and RUN. NOTE: The eighth turn must end in the RUN position.

The doors will lock, then unlock, to confirm that the programming mode has been activated.

Within 20 seconds press any button on the remote entry transmitter. NOTE: If more than 20 seconds have passed you will need to start the procedure over again.

The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed.

Repeat Step 6 to program each additional remote entry transmitter.

Turn the ignition to the LOCK position after you have finished programming all of the remote entry transmitters.

The doors will lock, then unlock, to confirm that the programming mode has been exited. Focus 2000-2007 Close doors, buckle seat belts, off to on 4x, tone, then depress remote button.